Your best expert on every shift, in every factory.
Your best expert on every shift, in every factory.
Your best expert on every shift,
in every factory.
Capture expertise, standardize effortlessly,
and guide every decision on the shop floor.
Capture expertise, standardize effortlessly,
and guide every decision on the shop floor.
Videos to SOP
Your most precious factory knowledge lives in your experts heads. Allude captures it and turns it into structured procedure in minutes, effortlessly.
STEP
1
Film it.
Film it.
Film your experts, operators, technicians or engineers doing a task. That's it.
Speaking...
Speaking...
Analyse
Alright, so today we're going to walk through the die changeover procedure on the hydraulic press — line 3. Thomas is going to perform the operation, I'll be guiding you through each step as we go.
First thing, always — before touching anything — is LOTO. Lock Out, Tag Out. Thomas is applying the lock to the main power panel right now. The machine needs to be at zero energy before we go anywhere near the die. This is non-negotiable.
Alright, so today we're going to walk through the die changeover procedure on the hydraulic press — line 3. Thomas is going to perform the operation, I'll be guiding you through each step as we go.
STEP
2
Allude creates a complete
Standard Operating Procedure (SOP)
Allude creates a complete
Standard Operating Procedure (SOP)
in minutes.
Structured, accurate, and ready to use.
Video to SOP
Search
All files
Date
CMMS Viewer
Maintenance / Hydraulic press - die changeover
Hydraulic press - die changeover
Mécatech Industries · Production line 3
Document ID
SOP-PRD-0042
Generated
28 May 2026
Est. duration
~25 min
Source
Video capture · 18 min
Procedure
1
Apply LOTO
Lock out and tag out the hydraulic press at the main power panel. Confirm zero-energy state before proceeding. Do not bypass under any circumstances.
Settings
Eva
Chat
Voice agent
Video to SOP
Sources
Folders
Security
12
Maintenance
29
Test
2
Equipment
8
Video to SOP
Search
All files
Date
CMMS Viewer
Maintenance / Hydraulic press - die changeover
Hydraulic press - die changeover
Mécatech Industries · Production line 3
Document ID
SOP-PRD-0042
Generated
28 May 2026
Est. duration
~25 min
Source
Video capture · 18 min
Procedure
1
Apply LOTO
Lock out and tag out the hydraulic press at the main power panel. Confirm zero-energy state before proceeding. Do not bypass under any circumstances.
Settings
Eva
Chat
Voice agent
Video to SOP
Sources
Folders
Security
12
Maintenance
29
Test
2
Equipment
8
Video to SOP
Search
All files
Date
CMMS Viewer
Maintenance / Hydraulic press - die changeover
Hydraulic press - die changeover
Mécatech Industries · Production line 3
Document ID
SOP-PRD-0042
Generated
28 May 2026
Est. duration
~25 min
Source
Video capture · 18 min
Procedure
1
Apply LOTO
Lock out and tag out the hydraulic press at the main power panel. Confirm zero-energy state before proceeding. Do not bypass under any circumstances.
Settings
Eva
Chat
Voice agent
Video to SOP
Sources
Folders
Security
12
Maintenance
29
Test
2
Equipment
8
STEP
3
Talk to Sam
Talk to Sam
Sam has learned how your factory works. Like an experienced colleague, he suggests a likely root cause for a problem and proposes an action plan to fix it. The final call is always yours.
Sam has learned how your factory works. Like an experienced colleague, he suggests a likely root cause for a problem and proposes an action plan to fix it. The final call is always yours.
Find the root cause
Sam finds them and ranks
them by likelihood
Get your action plan
Once the cause is confirmed,
Sam writes the plan for you
Locate the right part, instantly
No digging through systems —
Sam finds it in seconds
We have a contamination issue on chamber CH-07. Where could it be coming from?
ROOT CAUSES — RANKED BY LIKELIHOOD
Most likely
Contamination without chamber opening
WO 4521
WO 4498
WO 4472
+4 more
Often tied to extended idle time or buildup in the load lock.
Possible
Internal chamber fouling
WO 4390
WO 4210
Particle buildup on the dome or injector, sometimes after a wafer break.
Less likely
Degraded seal or gas line drift
WO 4102
Worth ruling out, though this pattern usually shows up more gradually.
Find the root cause
Sam finds them and ranks
them by likelihood
Get your action plan
Once the cause is confirmed,
Sam writes the plan for you
Locate the right part, instantly
No digging through systems —
Sam finds it in seconds
We have a contamination issue on chamber CH-07. Where could it be coming from?
ROOT CAUSES — RANKED BY LIKELIHOOD
Most likely
Contamination without chamber opening
WO 4521
WO 4498
+4 more
Often tied to extended idle time or buildup in the load lock.
Possible
Internal chamber fouling
WO 4390
WO 4210
Particle buildup on the dome or injector, sometimes after a wafer break.
Less likely
Degraded seal or gas line drift
WO 4102
Worth ruling out, though this pattern usually shows up more gradually.
Confirmed
Root cause confirmed:
seal degradation on CH-07
Sam's recommended action plan:
Lockout / tagout chamber CH-07 — LOTO-07
Replace worn vacuum seal → PN 4471-SEAL-A
Purge line and leak-test before restart
Contamination on chamber CH-07. Where's it coming from?
Seal degradation on CH-07
- linked to WO-4471
72%
Coolant line cross-contamination
19%
Operator handling
9%
Find the root cause
Sam finds them and ranks
them by likelihood
Get your action plan
Once the cause is confirmed,
Sam writes the plan for you
Locate the right part, instantly
No digging through systems —
Sam finds it in seconds
We have a contamination issue on chamber CH-07. Where could it be coming from?
ROOT CAUSES — RANKED BY LIKELIHOOD
Most likely
Contamination without chamber opening
WO 4521
WO 4498
+4 more
Often tied to extended idle time or buildup in the load lock.
Possible
Internal chamber fouling
WO 4390
WO 4210
Particle buildup on the dome or injector, sometimes after a wafer break.
Less likely
Degraded seal or gas line drift
WO 4102
Worth ruling out, though this pattern usually shows up more gradually.
Confirmed
Root cause confirmed: seal degradation on CH-07
Sam's recommended action plan:
Lockout / tagout chamber CH-07 — LOTO-07
Replace worn vacuum seal → PN 4471-SEAL-A
Purge line and leak-test before restart
Contamination on chamber CH-07. Where's it coming from?
Seal degradation on CH-07 - linked to WO-4471
72%
Coolant line cross-contamination
19%
Operator handling
9%
"Last week, a small mistake by a new technician stopped our line for 8 hours. It cost us €80,000 and it could have been avoided if our procedure didn't leave room to interpretation."
“Last week, a small mistake by a new technician stopped our line for 8 hours. It cost us €80,000 and it could have been avoided if our procedure didn’t leave room to interpretation. “
“Last week, a small mistake by a new technician stopped our line for 8 hours. It cost us €80,000 and it could have been avoided if our procedure didn’t leave room to interpretation. “
Maintenance manager, Global food manufacturer
Maintenance manager, Global food manufacturer
Maintenance manager, Global food manufacturer
Measurable ROI
Results visible from day one
of the pilot.
Results visible from day one of the pilot.
From our deployments with industrial clients in semiconductor, food, luxury, automotive and pharma.
87%
Adoption in 4 weeks
-26%
MTTR — mean time to repair
-82%
Documentation effort
4.2x
More tacit insights captured
See Allude in action.
Capture your first SOP in minutes.
See Allude in action.
Capture your first SOP in minutes.
See Allude in action.
Capture your first SOP in minutes.
You are one demo away from transforming
your operations.
You are one demo away from transforming
your operations.
Product
© 2026 Allude. All right reserved.
Product
© 2026 Allude. All right reserved.
Product
© 2026 Allude. All right reserved.